Two switches are members in an active Intelligent Resilient Framework (IRF) virtual device. A network administrator joins a third switch to the IRF virtual device. Which switch is now the master?

A. The current master of the IRF virtual device always remains the master.

B. The switch with the lowest member ID always becomes the master.

C. The switch with the lowest priority value always becomes the master.

D. The switch with the highest priority value always becomes the master.

A company wants a modular switch for the access layer at its main campus and for several branch offices. Which HP Switch Series is best suited for this role?

A. HP 11900

B. HP 12900

C. HP 5900

D. HP 5400R

Refer to the exhibit.

The physical interfaces for Comware-1 and Comware-2 switches in the exhibit are configured in routed mode and OSPF. Both switches have the three subnets in their routing tables. The administrator wants to use DHCP to assign addressing information to the users. Based on the exhibit, where should the administrator configure DHCP relay?

A. Comware-1. G1/0/2

B. Comware-1, G1/0/1

C. Comware-2. G1/0/2

D. Comware-2, G1/0/1

A network administrator is managing an HP Comware switch from the CLI. Which action can the administrator only perform in User view?

A. verifying connectivity with traceroute or ping tools

B. creating a VLAN and assigning ports to it

C. executing display commands

D. viewing files located in flash memory

Refer to the Exhibit.

Examine the output from the Comware command shown in the exhibit. Based on the flag of ACDEF, what is the status of the aggregated link?

A. Static LACP link aggregation is configured, and the aggregated link is operational with load sharing not being performed.

B. Static link aggregation is configured, and the aggregated link is operational with load sharing being performed.

C. Static LACP link aggregation is configured, and the aggregated link is operational with load sharing being performed.

D. Static link aggregation is configured, and the aggregated link is operational with load sharing not being performed.

Which HP solution provides network optimization and automated network provisioning to its customers?

A. Intelligent Management Center NTA

B. FlexNetwork Architecture

C. Intelligent Resilient Framework

D. Software-defined Networking

Refer to the exhibit.

The network administrator has configured this port to permit all VLANs. The output in the exhibit indicates that the port is only passing VLANs 1 and 11. The administrator wants the port to pass VLAN 12 as well. What should the administrator do to accomplish this?

A. Enable IP routing.

B. Add VLAN 12 to the switch.

C. Change the port link-type to hybrid.

D. Change the port link-type to access.

A network administrator wants to join a switch to an Intelligent Resilient Framework (IRF) virtual device. The administrator changes the switch member ID from 1 to 2. What must the administrator do before configuring the IRF port on this switch?

A. Physically connect the switch to the IRF master device.

B. Reboot the switch.

C. Disable IP routing.

D. Enable the physical interfaces that will be assigned to the IRF port.

A network administrator wants to establish an LACP link aggregation between an HP Comware switch and an HP ProVision switch. Which settings should the administrator configure?

A. The link aggregation mode should be set to static on the Comware bridge interface, and the ProVision trunk should be set to lacp.

B. The link aggregation mode should be set to dynamic on the Comware bridge interface, and the ProVision trunk should be set to trunk.

C. The link aggregation mode should be set to static on the Comware bridge interface, and the ProVision trunk should be set to trunk.

D. The link aggregation mode should be set to dynamic on the Comware bridge interface, and the ProVision trunk should be set to lacp.

On an HP Comware switch, which view must an administrator access in order to execute the debug command?

A. Manager

B. Operator

C. System

D. User