A network administrator is managing an HP Comware switch from the CLI. Which action can the administrator only perform in User view?

A. verifying connectivity with traceroute or ping tools

B. creating a VLAN and assigning ports to it

C. executing display commands

D. viewing files located in flash memory

A network administrator has copied new software to an HP ProVision switch and placed this software in the secondary flash location. The switch is currently booting from the primary flash location. The administrator wants the switch to start using the new software.

What should the administrator do to accomplish this?

A. Execute the command to boot the system from the secondary flash.

B. Reboot the switch, which automatically causes the switch to use the newer software.

C. Copy the secondary software to the primary software slot.

D. Rename the secondary software as the primary software.

Refer to the exhibit.

The switches in the exhibit are all HP Comware switches that run Multiple Spanning Tree Protocol (MSTP).

The network administrator wants to ensure that each switch-to-switch link is in its own subnet. The administrator also wants to make sure that all of the links are available for routing during normal operation. How should the administrator configure the physical switch-to-switch interfaces to accomplish these goals?

A. Configure them as trunk ports that permit VLANs 10 and 20.

B. Configure them as any type of port, and make sure spanning tree is enabled on them.

C. Configure them as route-mode ports.

D. Configure them as hybrid ports that carry VLAN 10 and 20 as untagged.

Which ProVision configuration includes 10.0.3.0/24, which represents VLAN 30 in OSPF area 0?

A. vlan 30 ip ospf area 0

B. vlan 30 area 0

C. interface vlan 30 ip ospf area 0

D. router ospf area 0 vlan 30

Which credential is required to validate SNMPv2c write requests?

A. Community string

B. Scheme

C. MD5 authkey

D. AAA authentication

When configuring Multiple Spanning Tree Protocol (MSTP), how should VLANs be separated to perform load balancing?

A. placed into separate instances

B. configured with different priority values

C. never configured with more than one VLAN per instance

D. placed into separate regions

Refer to the exhibit.

Switch-1 is an HP ProVision switch.

A network administrator wants Switch-1 to run Open Shortest Path First (OSPF) and create neighbor relationship on Links 1 and 2. What should the administrator do to accomplish this?

A. Access the VLAN context for the VLANs assigned to Links 1 and 2, and enable OSPF.

B. Access the global configuration context, and create OSPF routes to 10.0.1.0/24 and 10.0.2.0/24.

C. Access the physical interface context for the Link 1 and 2 ports, and enable OSPF.

D. Access the OSPF area 0 context and specify the networks on Links 1 and 2 (10.0.1.0 0.0.0.255 and 10.0.2.0 0.0.0.255).

A company has a network comprised of HP Comware and ProVision switches. A network administrator purchases HP Intelligent Management Center (IMC) to manage the switches in this network. Which step must the administrator perform on the Comware switches but not on the ProVision switches?

A. Configure SNMP traps.

B. Configure VTY interface authentication.

C. Define SNMPv2 community strings or SNMPv3 groups and users.

D. Configure telnet or SSH.

A network administrator is configuring a static route. What should the administrator use as the next hop address?

A. the IP address on the local interface that is used to egress traffic towards its destination

B. the lowest IP address on the neighboring router in the path towards its destination

C. the IP address on the connected interface of a neighboring router in the path towards its destination

D. the IP address of the default gateway in the destination subnet

A network administrator wants to establish an LACP link aggregation between an HP Comware switch and an HP ProVision switch. Which settings should the administrator configure?

A. The link aggregation mode should be set to static on the Comware bridge interface, and the ProVision trunk should be set to lacp.

B. The link aggregation mode should be set to dynamic on the Comware bridge interface, and the ProVision trunk should be set to trunk.

C. The link aggregation mode should be set to static on the Comware bridge interface, and the ProVision trunk should be set to trunk.

D. The link aggregation mode should be set to dynamic on the Comware bridge interface, and the ProVision trunk should be set to lacp.