Correct Answer: ADE

Explanation: You can create three different types of interface groups on your storage system: single-mode, static multimode, and dynamic multimode interface groups.

Reference: Types of interface groups

https://library.netapp.com/ecmdocs/ECMP1196907/html/GUID-EFA72201-E035-41E2-AC53CD81A472B5ED.html

Correct Answer: BD

Explanation: The minimum number of disks in a RAID-DP group is three: at least one data disk, one regular parity disk, and one double-parity (dParity) disk. However, for non-root aggregates with only one RAID group, you must have at least 5 disks (three data disks and two parity disks).

Reference: Clustered Data ONTAP 8.3, Physical Storage Management Guide, page 108

https://library.netapp.com/ecm/ecm_download_file/ECMP1636022

Correct Answer: C

Explanation: Before you set up NetApp CN1610 cluster switches verify that you have the appropriate FASTPATH firmware and reference configuration file (RCF) versions for your version of Data ONTAP.

Incorrect:

Not A, Not C: NetApp CN1610 will work fine. If you have an existing two-node switchless cluster

environment, you can migrate to a two-node switched-cluster environment using CN1610 cluster network

switches.

Reference: Clustered Data ONTAP Switch Setup and Configuration Guide, page 15

http://www-01.ibm.com/support/docview.wss?uid=ssg1S7004655andaid=1

Correct Answer: BCE

Explanation: C: If you are adding nodes to a multiple-node cluster, more than half of the existing nodes in the cluster must be healthy (indicated by cluster show).

E: If you are adding nodes to a two-node switchless cluster, you must have installed and configured the

cluster management and interconnect switches before adding additional nodes.

Incorrect:

not A: If you are adding a second node to a single-node cluster, the second node must be installed, and the

cluster network must be configured. Not D: The switchless cluster functionality is supported only in a two-

node cluster.

Reference: Adding nodes to the cluster https://library.netapp.com/ecmdocs/ECMP1636037/html/GUID-B13FF812-785E-4E62-991430E7A8F51A4C.html

Correct Answer: BC

Explanation: Cisco NX5596 is a cluster interconnect switch. NetApp CN1610 is a cluster interconnect switch that can be used for FAS8040 nodes.

Incorrect:

Not A: The Cisco Catalyst 2960 is not a cluster interconnect switch. Not D: NetApp CN1601 is a cluster

management switch.

Reference: Clustered Data ONTAP 8.3, Express Setup Guide for 80xx Systems

Correct Answer: ABE

Explanation: The Hardware Universe (HWU) application is NetApp's system configuration solution, replacing the System Configuration Guides.

Correct Answer: B

Explanation: IPspaces enable you to configure a single Data ONTAP cluster so that it can be accessed by clients from more than one administratively separate network domain, even if those clients are using the same IP address subnet range.

Reference: Clustered Data ONTAP 8.3, Network Management Guide, page 32

Correct Answer: D

Correct Answer: D

Explanation: The NetApp Best Practice specifies that Flow Control settings for 10G cluster ports are to be set with Flow Control = None.

Reference: How to modify the Flow Control setting on clustered Data ONTAP cluster ports

https://kb.netapp.com/support/index?page=contentandid=1015245andactp=LIST_RECENT

Correct Answer: BDE

Explanation: ADP supported platforms:

B, D: 2200, 2500 (Internal drives): Root Data Slice (HDD), Root Data Slice (AFF ?All Flash FAS)

E: 3200, 6200, 8000 ( 48 drives) : Root Data Slice (AFF ?All Flash FAS) Example ADP configuration: FAS8040 All-Flash (36 x 800GB SSD)

Reference: NETAPP DATAONTAP 8.3 | ADP ROOT DISK-SLICE DEEP-DIVE

http://www.datacenterdan.com/blog/netapp-dataontap-83-adp-root-disk-slice-deep-dive