Scenario: A Citrix Administrator has a NetScaler SDX appliance with several instances configured. The administrator needs one instance with two interfaces connected to forward packets that are NOT destined for its MAC address. Hence, the administrator has enabled Layer 2 mode. After enabling Layer 2 mode, the administrator found the interface status going up and down.

What can the administrator perform to resolve this issue?

A. Disable Layer 2 mode on a NetScaler instance.

B. Enable MAC-based Forwarding mode.

C. Enable tagging on all interfaces.

D. Enable Layer 3 mode along with Layer 2 mode.

Users are experiencing resets form the Intranet server website, which is load-balanced trough the NetScaler.

Which NetScaler tool can a Citrix Administrator use to troubleshoot the reset issue?

A. Take a packet trace with nstrace and analyze with WireShartk.

B. Look in the Event Viewer for packet resets from the NetScaler.

C. View the new nslog form the command-line interface to look for packet resets form the NetScaler.

D. Use the nslog to look for packet resets on the NetScaler.

Which type of entity can a Citrix Administrator configure to support the use of an SSL rewrite policy?

A. Global server load balancing virtual server

B. Content Switching virtual server

C. SSL load balancing virtual server

D. SSL_Bridge balancing virtual server

A Citrix Administrator has deployed a new NetScaler MPX appliance in the demilitarized (DMZ) with one interface in the DMZ and the other on the internal network.

In which mode should the administrator deploy the NetScaler?

A. One-Arm

B. Two-Arm

C. Forward Proxy

D. Transparent

After creating and correctly configuring a custom user monitor, from where do the monitor probes originate by default?

A. Subnet IP address

B. NetScaler IP address

C. Mapped IP address

D. Virtual IP address

Scenario: A Citrix Administrator needs to create local user accounts for other administrators with limited privileges. The other administrators will need only:

-Read-only access -The ability to enable and disable services and servers

Which built-in Command Policy permission level can the administrator use?

A. Network

B. Operator

C. Sysadmin

D. Read-Only

Scenario: A Citrix Administrator entered the command-line interface commands below to prevent IP address 10.10.100 from accessing the NetScaler on port 80.

add simpleacl rule1 DENY- srcIP 10.10.10.100 –TTL 600 add simpleacl rule2 DENY- srcIP 10.10.10.100 –destPort 80 add ns acl rule1 DENY- srcIP 10.10.10.100-priority 10 add ns acl rule2 DENY- srcIP 10.10.10.100-priority 100 apply ns acls

Which Access Control List (ACL) will the NetScaler use to deny the IP address?

A. add ns acl rule1 DENY-srcIP 10.10.10.100-priority 10

B. add simpleacl rule1 DENY- srcIP 10.10.10.100 –TTL 600

C. add simpleacl rule2 DENY- srcIP 10.10.10.100 –destPort 80

D. add ns acl rule2 DENY- srcIP 10.10.10.100-priority 100

Where should a Citrix Administrator configure SmartControl restrictions?

A. Citrix Gateway

B. XenDesktop Delivery Controller

C. Citrix Gateway, Citrix Delivery Controller and StoreFront

D. StoreFront and Citrix Delivery Controller

Scenario: A Citrix Administrator manages an environment that has multiple websites running through a NetScaler MPX 5550. The NetScaler meets the needs of the environment throughout the year, except in December, when the capacity doubles. The administrator needs to handle this increased web traffic with a temporary, cost-effective solution. Which action should the administrator recommend in order to handle the increased web traffic?

A. Purchase a BurstPack License

B. Purchase NetScaler Gateway Platform License

C. Purchase a license to upgrade the MPX 5550 to a MPX 5650

D. Purchase Universal License

Scenario: User authentication is failing through the NetScaler. A Citrix Administrator checked the Authentication, Authorization and Auditing (AAA) policy, action and virtual server and verified that the correct configuration was in place. The administrator bypassed the NetScaler and the authentication worked. Which NetScaler utility can the administrator use to troubleshoot the access issue?

A. nslog file

B. aaad.debug

C. nscon message

D. Dashboard