Your company is looking for a simplified method for managing a group of reports. Identify the type of report used in WMS Cloud that compiles multiple existing reports into a single document while executing each report in a single order.

A. CrossTab Report

B. Express Report

C. Linked Report

D. Chained Report

E. Standard Report

Your customer wants to receive an IB shipment and capture pallet weight at the time of receiving. Which parameter must be set in the Receiving RF screen to meet this requirement?

A. Set Capture-catch-weight as "Prompt for catch wt".

B. Set Mode as Blind-ASN Receiving.

C. Set rch-sku-not-on-shmnt to "Promt for catch wt".

D. Set Single-Sku-management as Assume Single SKU.

E. Set Blind-License Plate Number-receive-mode as by SKU scan.

The following configuration is set for the Advance Shipment Notification type: 10% Under Receipt Warning, 10% Over Receipt Warning, and 20% Over Receipt error. Which two statements match the condition set if the ASN Qty is 100? (Choose two.)

A. When the Operator receives 125 units, the RF screen displays an Over Receipt warning message.

B. When the Operator receives 101, the RF screen displays an Over receipt warning message.

C. When the Operator receives 110, the RF screen displays an Over Receipt warning message.

D. When the Operator receives 89, the RF screen displays an Under Receipt warning message.

E. When the Operator receives 130 units, the RF screen displays an Over Receipt error message.

When creating an Appointment, which three "Matching value type" selections can be used to create the Appointment? (Choose three.)

A. License Plane Nbr

B. Load Nbr

C. Dock Door

D. PO Number

E. Advance Shipment Notification

F. Trailer Nbr

You are configuring the WMS Cloud to have multiple facilities and, as an added measure of control, you

want to easily identity the facility by looking at the barcode printed on the outbound carton.

Identify two valid configurations that are available in the Sequence Counter UI that you can use for the

OBLPN. (Choose two.)

A. You can set up the count increment in Facility 1 to increase by 1, the count increment in Facility 2 to increment by 2, and so on.

B. You can set up the sequence counter OBLPN to "Append Facility Code to Prefix".

C. You can specify different counts for the different facilitates within the Sequence Counter.

D. You can configure the sequence length for this facility to be different from the other facilities.

E. You can specify the "Color Code" in the Sequence Counter.

What happens behind the flag Only deallocate on Short in the order type screen?

A. The Order Type has no impact on the Picking Process.

B. When the parameter is set to YES, during short pick, the system will put the order hold status until more inventory is available.

C. When the parameter is set to Yes, then only the shorted quantity will get deallocated form the order.

D. When the parameter is set to No, the shorted quantity on the order remains in the "allocated" status.

E. When the parameter is set to Yes, the short pick will cancel the shorted order line automatically and inventory adjustment will be generated for the item.

A user is using the PackNC transaction to pack into a blind OBLPN. The user needs to pick up 10 units for

Item 000234, but after picking up four units the OBLPN is full.

What should the user do?

A. move to the next location

B. end the LPN

C. short the remaining units

D. scan the next order

What configuration is needed to create Advance Shipment Notifications for a Transfer Order shipped between two facilities configured in the same WMS Cloud environment?

A. The Facility parameter key AUTOLOAD_and_SHIP should be set to Yes.

B. The "ACCEPT TRANSFER SHIPMENT" flag should be enabled on the Facilities UI screen for the Source Facility.

C. The "ACCEPT TRANSFER SHIPMENT" flag should be enabled on the Facilities UI screen for the Destination Facility.

D. Set CREATE_ASN_FOR_EACH_PO to YES at Source and Destination Facility levels.

E. Set CREATE_ASN_FOR_EACH_PO to YES at the Company level.

During which of the following three scenarios does the WMS validate or throw an error message during picking with a serial number tracking execution? (Choose three.)

A. When the scanned serial number is not present in the scanned IB LPN or Outbound LPN or item and is present for a different facility.

B. When the scanned serial number is present in the scanned IB LPN or active location and also exists for another item in stock in the current facility.

C. When the scanned serial number is not present in the scanned IB LPN or Outbound LPN or item and is currently linked to another Inventory Record for the facility.

D. When the scanned serial number, which is associated with an OBLPN in shipped status for a different facility, is not found for the current facility.

E. When the same serial number, which is already present on the same Sku in a different facility, is scanned.

Your customer wants to use Advance Shipment Notification (ASN) created in WMS Cloud System for receiving without RF gun and expects ASN to be verified. What are the two steps to complete the ASN receiving and verification transaction? (Choose two.)

A. Create a Blind IB plate number and palletize after receiving

B. Create a Blind IB plate number and cartonize before receiving

C. Assign a dock door to IB shipment

D. Create an ASN from the IB license plate screen

E. Verify the IB shipment