Your customer has a communication Manager 6.0 branch location with SIP endpoints that need to survive a WAN failure when communication to the core or main Session Manager is unavailable. Which solution will provide survivability to the remote location?

A. an S8300 configured as an local survivable processor (LSP)

B. a simplex server configured as an enterprise survivable server (ESS)

C. an S8300 or simplex server configured as a Survivable Remote

D. an S8300 01 simplex server configured for high availability (HA)

Consider the settings shown in exhibit displayed by using the display route ?pattern command. You must deny calls from users in COR 10 to use route pattern 1. What should the fault restriction level (FRL) for COR 10 be?

A. 2

B. 3

C. 4

D. 5

E. 6

With reference to the list trace station 1101 printout shown in the exhibit, what statement describes what happened during the time period of the trace?

A. Station 1101 called station, hung-up and finally called station 100.

B. Station 1101 called station 1000, the unanswered call went to the voicemail, and finally station 1101 called 1001.

C. Station 1101 called station 1000, and the station answered, then station 1000 transferred to call to station 1001.

D. Station 1101 called station 1000, unanswered; the call covered the station 1001.

You are configuring Personal Station Access (PSA) and you configure the Communication Manager with the following settings:

-

Set TTI enabled = `Y'

-

Set PSA Associated code = `25' and disassociate code `#25'

-

Set security code for the station = `1234'

You activate the station by keying in FAC for PSA, station extension number, `#', the security code of the station, and `#'. However, the station is not activated. Which statement describes the issue to be addressed?

A.

You need to set TTI = `n'

B.

You did not enable PSA on the COS of the station.

C.

You should not set the security code in sequential order.

D.

You did not key in the correct activation sequence

The monitor and display capacity commands can be used to get a real-time status of the system using Avaya Site Administration (ASA). Which command and tool should you use to view a summary of the overall condition of the system?

A. monitor system command using terminal emulation

B. monitor system command using GEDI

C. monitor status command using terminal emulation

D. display status using GEPI or terminal emulation

Which statement most accurately describes the function of automatic call back feature?

A. It allows internal users who placed a call to a busy or unanswered external telephone to be called back when the called telephone becomes available.

B. It allows internal users who placed a call to a busy or unanswered internal telephone to be called back when the called telephone becomes available.

C. It allows internal users who are called when they are busy to activate a feature to automatically call back that second caller, once the first call is finished.

D. It allows internal users who are called when they are busy to place the second call on hold until the first call is finished.

With consideration to the exhibit, in which hardware component do you configure the IP address 150.122 44 210?

A. In the Media Gateway

B. In the Server administration port C. In a CLAN board or Processor Ethernet port

D. In the Server services port

In addition to protocol and function, which two other factors affect the choice of trunk type? (Choose two)

A. number of users

B. link bounce timer value

C. type of endpoints

D. distance

E. type of gateways

Your Avaya Aura?Communication Manager System has been operating without Incident for several months. Then, one day at 10:00 AM, you get multiple reports about blocked access and users unable to make calls. You run Processor Occupancy Summary and Trunk Group Summary reports and determine that there are no issues with processor occupancy or availability of trunks. So now you decide to see if someone made a change to the system around 10:00 AM. Which report will show what administrative or maintenance system changes that were made around 10:00 AM and by whom?

A. a history report

B. an activity performed report

C. an administrative or maintenance summary report

D. a hardware error log report

E. a system-parameters change report

Changes that an administrator performs on a system are always only written to ---- RAM. Which SAT command must be used to copy these changes so that the hard disk, so that in case of a loss of power, the changes will be available?

A. save -----

B. copy running configuration startup configuration

C. copy ------ all

D. save ------ startup configuration