The attempt to manage an Ethernet Routing Switch (ERS) 8000 using a Virtual Route Redundancy Protocol (VRRP) address was not successful. What is causing this problem?

A. The virtual router identifier is 0.

B. The data center interface is set as a critical IP interface.

C. A real IP address is required for management access not a VRRP address.

D. The virtual router identifier is configured for the VRRP IP address owner.

A technician is configuring an InterSwitch Frank (IST) for Spilt Multi-Link Franking (SMLT). Which statement about how the IST is addressed is true?

A. Configure the IP address of the ports that comprise the IST.

B. No address configurations are required when configuring an IST.

C. Configure the IP address of the VLAN that was created for the IST.

D. Configure the MAC addresses of the switches on each end of the IST.

By default the ERS 8000 is configured for warm standby. After installation of a new ERS solution with dual CPUs, which three actions need to be Perform on the ERS configuration to ensure high availability mode is enabled and will function correctly? (Choose three)

A. Set the high availability CPU boot flag to true.

B. Set the warm standby CPU hoot flag to false.

C. Set the save to standby CPU boot flag to true.

D. Save the boot.cfg conflg file and reset the switch to activate the changes.

E. Install the high availability license file.

Simple Loop Prevention Protocol (SLPP) detects VLAN based network loops. Which two statements about SLPP functionality are correct? (Choose two.)

A. Spanning tree packets on a per VI AN basis allow SLPP to detect VI AN based network loops.

B. SLPP packets on a peer VLAN basis allow SLPP to detect VLAN based network loops.

C. The port is shut clown when a loop is detected.

D. The port on the edge switch of the link is disabled when a loop is detected.

One of the benefits of the Ethernet Routing switch (ERS) 8300 switch is its ability to provide power- over-Ethernet (PoE). When implementing PoE on the ERS 8300 there are certain power supply requirements to consider. The 8301AC produces 1140W and 1770W and the 8302AC produces 850W and 1400W depending on the input voltage for both cases.

If there are eight 8648TX-PWR modules in a chassis, each needing 200W for Powered Devices (PI)) which power supply configuration is recommended?

A. One 8301AC power supply with 240VAC input voltage

B. Two 8302AC power supplies with 120VAC input voltage

C. Three 83CAC power supplies with 240VAC input voltage

D. Two 8301AC and one 8302Ac for redundancy with 240VAC input voltage

A split Multi-Link Trunking (SMLT) for switch clustering is being configured. Which statement is a configuration requirement for the SMLT?

A. CP-Limit is configured on edge switch stacks.

B. Neighboring edge switch stacks should be connected to each other via a DMLT connection to add resilient paths in the event of an SMLT failure.

C. Alternate the primary path of the SMLT connection to load balance the switch core.

D. VLANS that are defined on the SMLT are so defined on the MLT that defines the core Inter Switch Trunks (IST)

A technician is configuring a Link Aggregation connection from a stack of Ethernet Routing Switch (ERS) 5500 lo a core pair of ERS 8600 switches. Which statement about the correct uplink configuration is true?

A. Distribute uplinks across different ERS 5500 switches in the stack.

B. Disable auto negotiation and replace it with VLACP to identify single fiber fault failure

C. Use unique MLT IDS for each stack of edge ERS 5500 switches

D. Enable Spanning Tree Protocol for the MLT when using it with SMLT in the core of the network.

In Ethernet Routing Switch (ERS) 5600 switch was added into the existing ERS 5500 stack, but ft did not form a proper stack. Which statement describes the problem?

A. The ERS 5600 was set as the Base Unit.

B. The stack was reset for a change in Base Unit to take effect.

C. The mode parameter on the ERS 5600 switch was set to Mixed Mode.

D. The ERS 5500 was set as the Base Unit.

Confirm that RSMLT will work on a set of VLANs. Which network design aspect should be considered?

A. RSMLT is enabled on each SMLT VLAN on which the function is required

B. RSMLT is enabled on the VLAN group.

C. Router 1 always owns the network.

D. RSMLT is enabled on all SMLT VLANs.

Which statement describes how to configure Simple Loop Prevention protocol (SLPP) Rx?

A. SLPP is configured on the edge switch ports that connect to the core switch cluster.

B. SLPP is configured on the core switch cluster ports that connect to the edge switch.

C. SLPP is configured on the Inter Switch Trunk (1ST) ports of the core switch cluster.

D. SLPP is configured on the uplink ports of both the core switch cluster and the edge switch