What is the maximum number of hosts supported in a VxRail Stretched Cluster?

A. 15

B. 16

C. 31

D. 32

What is the recommended way to power up VxRail E, V, P, and S Series nodes?

A. Ensure the System Health indicatorblinks amber for 10 minutes after power on

B. Use the power button on the rear panel to power on each node

C. Wait at least 30 seconds between powering up each node

D. Use the iDRAC interface to power on each node

What is a consideration for using link aggregation on the Top of Rack (ToR) switch for a VxRail?

A. Should not be used for VxRail node ports, but can be used for uplink and ISL

B. Is not supported on the VxRail ToR switch

C. Can be configured for any connectivity, but are not required

D. Should always be configured for VxRail node ports to allow for failover

Based on the exhibit, which interfaces should be used to reset the node through the Mobile Build Server?

A. 1 and 3

B. 1 and 2

C. 2 and 3

D. 1, 2 and 3

A company is planning to deploy VxRail for business critical applications. The solution should support

automated workload re-balancing.

Which vSphere license is required for this solution?

A. vSphere with Operations Management Enterprise

B. vSphere Enterprise Plus

C. vSphere Enterprise

D. vSphere Standard

A company has a simple, 4 node VxRail cluster. The VxRail is running version 3.5 and utilizes a vSphere

standard license. The company has asked for a VxRail software upgrade.

What are the steps for the upgrade?

A. Log in to VxRail Manager, select "Internet Upgrade", then follow the prompts.

B. Log in to support.emc.com and download the upgrade packages.Next, open VxRail Manager, select "Off-line Upgrade", then follow the prompts.

C. Place all four nodes into maintenance mode.Next, log in to VxRail Manager, select "Internet Upgrade", then follow the prompts.

D. Contact Dell EMC support to request the upgrade to the VxRail cluster.

A company has a two chassis G Series cluster and wants to change the setup. This will require a reset of

the chassis.

What is the correct procedure?

A. Reset both chassis simultaneously through the reset script

B. Reset the primary chassis first, followed by the secondary chassis, through the reset script.

C. Reset both chassis simultaneously with the mobile build server

D. Reset the secondary chassis first, followed by the primary chassis, through the reset script.

When validating the VxRail health just after the VxRail initial configuration, there is a red exclamation mark on the MARVIN-Virtual-SAN-Cluster and the reported health alarm is `Component metadata health'. A "Retest" action in the health service panel is performed and all the nodes in the cluster show health status as failed with the invalid state. Investigation does not reveal any hardware issues with the disks in use by

vSAN.

What action should be taken next?

A. Wait 24 hours, then click the "Retest" button again

B. Apply the vSphere ESXi600-201611001 patch, then click the "Retest" button again

C. Evacuate and destroy the disk/disk group that contains the component(s) reporting errors and clear the alarm

D. Reapply the MARVIN storage policy to the VxRail internal virtual machines

Which network traffic types require the specification of a VLAN ID in the VxRail Pre- Installation Site Checklist?

A. Fault Tolerance, vMotion, vSAN, and user VM Network

B. Management, vMotion, and vSAN only

C. Management, vMotion, vSAN, and user VM Network

D. vMotion, vSAN, and user VM Network only

During a node add procedure the new node cannot be discovered. A ping to the IPv6 address is

responding.

What could be the cause of this issue?

A. Only one network interface is up on the new node

B. vSAN VLAN is not configured correctly

C. Management VLAN ID is not set on the vmk0 interface

D. Loudmouth process is not running