Match the HP network infrastructure product to its HP FlexNetwork component.

Hot Area:

Hot Area:

Refer to the exhibit.

Switch 3 runs Rapid Per-VLAN Spanning Tree Plus (RPVST+), which is enabled on VLANs 1-4. Select the correct number for each of these parameters.

Hot Area:

Hot Area:

Refer to the exhibit.

Switch 1 and switch 2 run open Shortest Path First (OSPF) on all VLANs. Both switches establish an OSPF adjacency to a router at the main data center. Exhibit shows shoes some virtual Routing Redundancy Protocol (VRRP) and OSPF settings on Switch 1 during normal operation.

How can a network administrator increase the resiliency of this solution?

A. Implement Bidirectional Forwarding Detection (BFD) on the peer keep alive link between the core switches.

B. Change the VLAN 10 subnet to a /24 subnet and enable VRRP on it. Place Switch 2's link to the main data center in this subnet.

C. Make sure that, in each VRRP instance, each switch has a VRRP preempt delay of several minutes.

D. Configure Switch 1 as an OSPF graceful restart helper in VLAN 11 and Switch 2 as a helper in VLAN 10

Refer to the exhibit.

An HP Comware Switch connects to Voice over (VoIP) phones. The phones connect to user's computes, so each switch port connects a computer and a phone. These are the specifications:

The VLAN for data traffic is VLAN3

The VLAN for traffic VoIP is VLAN11

The phones support Link Layer Discovery Protocol (LLDP) Media Endpoint Detection (MED).

The network administrator wants to use LLDP-MED to advertise the voice VLAN ID and priority settings to the phones. The phones will then send tagged traffic in that VLAN. The switch should not check the incoming traffic's MAC address

against its voice OID list. The exhibit shows the applicable switch port configuration.

Which additional step must the administrator complete to accomplish this?

A. Enable voice VLAN 11 (voice vlan 11 enable)

B. Change the port to trunk mode (port link-type trunk)

C. Enable LLDP compatibility with Cisco Discovery Protocol (CDP) (lldp compliance admin-status cdp txrx)

D. Enable the port to advertise voice VLAN 11 with LLDP (lldp voice-vlan 11)

A company needs a simple authenticate solution for guests. The HP Comware access layer switches will implement portal authentication (or Web-Auth). The network administrator wants the switch to host the login web page on an IP address that not used for any other purpose.

What should the administrator do to accomplish this goal?

A. Set the IP address when defining the local portal server, and create a loopback interface for the address

B. Create RADIUS scheme that specifies this IP address for the authentication server. Select this scheme for portal authentication in the default domain

C. Create a layer 3 interface for the guest VLAN and assign the desired IP address. Activate local portal authentication on this interface.

D. Set the IP address when defining the local portal server, and the switch automatically begins using that address.

Two HP 10500 Series Switches connect on a 10G fiber link. One of the two fibers in the link breaks, and a broadcast storm occurs. How could a network administrator prevent a problem like this from happening again?

A. Configure Device Link Detection Protocol (DLDP) on both sides of the link.

B. Use Rapid Per VLAN Spanning Tree Plus (RPVST+) instead of Multiple Spanning Tree Protocol (MSTP).

C. Implement sFlow or NetStream on both sides of the link, setting the collector to an Intelligent Management Center (IMC) server.

D. Add another 10G link and create a link aggregation group on each switch that includes both links.

An HP Provision switch port is implementing MAC Authentication (MAC-Auth) to a RADIUS server. A device connects to the port, and the switch submits a RADIUS Access-Request to the server. What correctly describes how the switch determines the username and password for the request?

A. Depending on the configuration, the switch sends the device MAC address for the username or a configured username. It sends the device MAC address for the password or a configured password

B. The switch always sends the device MAC address as the username. It always sends "provision" for the password, and this password cannot be reconfigured.

C. The switch always sends the device MAC address as the username. Depending on the configuration, the password is the device MAC address or a configured password.

D. The switch always sends the device MAC address as the username and the password, and this behavior cannot be reconfigured.

Refer to the exhibit.

The five routers shown in the exhibit are successfully implementing OSPF on the interface shown in the exhibit. The exhibit also shows settings for OSPF areas and interface costs. A network administrator enters these commands on Router 4 and Router 5:

Which statement correctly describes the OSPF routing table on Router 2?

A. It has one next hop for 172.16.0.0/16, 10.0.0.6

B. It has one next hop for 172.16.0.0/16, 10.0.0.2

C. It has not learned a route to 172.16.0.0/16

D. It has one next hop for 172.16.0.0/16, 10.0.0.6, and 10.0.0.2

Refer to the exhibit.

This HP 10500 Switch Series is receiving an average of 1 Gbps of HTTP traffic from 10.1.4.0/24. The switch starts to receive an additional 1 Gbps of HTTP traffic from 10.1.4.0/24. How does the switch handle the traffic?

A. It drops the traffic

B. It forwards the traffic but marks it yellow (for a higher drop precedence)

C. It forwards the traffic without remarking it in any way

D. It forwards the traffic but marks it for forwarding in a lower priority queue

Refer to the exhibits. Exhibit 1 Exhibit 2

Exhibit 2 shows the Virtual Router Redundancy Protocol (VRRP) configuration and status for VLAN 3 on switch 1 during normal operation, when both Switch 1 and Switch 2 are up. Switch 1 then experiences a power failure. After a few

minutes, power is restored, and the switch comes back up.

What happens to VRRP operations in VLAN 3?

A. Switch 1 becomes Master two minutes after its VRRP processes up.

B. Switch 2 remains Master Switch 1 receives an error and stops participating in VRRP

C. Switch 2 remains Master, and Switch 1 becomes a Backup router.

D. Switch 1 becomes Master as soon as its VRRP processes come up.