You have to disable a switch that is connected to a port on your FAS2750. You notice that the LIFs that are

associated with this port are migrated to a port that is not expected.

In this scenario, what would cause this behavior?

A. The network port is configured incorrectly.

B. The broadcast domain is configured incorrectly.

C. There are no online ports within the same failover group.

D. The network failover port is not licensed.

Select the Exhibit tab.

Referring to the exhibit, a customer wants to migrate LIF lif1_iscsi to node cluster1-02 port e0d, but they receive an error.

What is the cause of this error?

A. The LIF is not properly configured.

B. The designation port is not available.

C. This type of LIF cannot be migrated.

D. The LIF does not have a failover group.

According to NetApp best practices, how many NTP servers should you associate with an ONTAP cluster?

B. 1

C. 3

D. 4

You want to expand an existing FAS8060 switchless cluster running ONTAP 9.5 with an AFF A300 system.

Which action should you take to perform this task?

A. Execute the cluster setup command on the existing FAS8060 cluster, add the cluster interconnect switches, and cable both the FAS8060 cluster and the AFF A300 system to the new cluster.

B. Create a separate switchless cluster with the AFF A300 system.

C. Connect the cluster ports of the AFF A300 system to the existing FAS8060 cluster, and join the existing cluster.

D. Add and configure the cluster interconnect switches, re-cable the FAS8060 cluster, add the AFF A300 system, and join the existing cluster.

You install a new FAS26xx HA system with ONTAP 9.5 at a customer's site. After cabling the SAS cables, the customer wants to cable Alternate Control Path (ACP). But the FAS26xx has no physical port for ACP.

Which statement is correct in this scenario?

A. Within a FAS HA system, the ACP function is established over the cluster interconnect

B. To reach the ACP function, you should put the ACP cable into one of the onboard Ethernet pons.

C. The ACP function is established over the customer network.

D. Beginning with ONTAP 9 software. ACP cabling for disk shelves is no longer required.

Referring to the exhibit(Missing the exhibit), which statement describes the duster network used by the cluster interconnect ports?

A. The network that allows all nodes in the cluster to have direct access to every other node's disk shelves.

B. The network used to allow all nodes to communicate with the users for data access.

C. The network used to allow all nodes to communicate with the customer (or management access.

D. The network used to allow all nodes to communicate for internal (private) data access.

You are preparing for a new installation. While determining the most suitable version of ONTAP software to deploy, you want to verify the ONTAP 9 release cadence to ensure that you are deploying a Long Term Service (LTS) release.

In this scenario, where would you find this information?

A. Visit the NetApp Support site.

B. Visit the ONTAP 9 Documentation Center site.

C. Visit the Interoperability Matrix Tool site.

D. Visit the Hardware Universe site.

A customer has a 6-node AFF A700 cluster and wants to add four nodes without having to update license functionality for each node manually.

In this scenario, which type of license provides this functionality?

A. Demo License

B. Site License

C. Standard License

D. Evaluation License

You are performing a nondisruptive image upgrade of a CN1610 switch. You verify that there are no path failures on the switch.

What is the next step in this process?

A. Run the write memory command.

B. Run the reload command.

C. Backup the current running image using the copy active backup command.

D. Reboot the switch.

A customer has recently purchase a new ONTAP 9.0 storage system and wants you to join the nodes to an existing cluster running ONTAP 9.5.

What is the first step for adding the new controllers to the existing cluster?

A. You must ensure that all network switches are upgraded and online.

B. You must configure the existing cluster to accept the Joining nodes.

C. You must make sure that there Is the same amount of disk shelves attached to all nodes.

D. You must match the operating system.