You are provisioning a LUN using an ISCSI initiator on an ESX host. You disable Ethernet flow control for

all ports but are experiencing Performance issues.

In this scenario, which two actions would improve the performance issue? (Choose two.)

A. Set the MTU settings 1500 for optimal performance.

B. Dedicate your ports to ISCSI traffic.

C. Enable jumbo frames across the entire data path.

D. Confirm that your host .mil storage polls are connected to a different network.

An enterprise customer has both a NetApp FAS8200 4-node cluster and a third-party storage array in a shared SAN environment. The host servers connect to both storage vendors' arrays in the fabric. Regarding (he hosts in this scenario, what are- two NetApp best practices when performing this task? (Choose two.)

A. Set the default timeout values and storage parameters for the host system.

B. Provide isolation between storage systems using NetApp's multitenancy feature.

C. Always use the same adapter for heterogeneous storage systems.

D. Use separate adapters to connect to each vendors' storage system.

You are testing iSCSI LUN failover across a 4-node FAS9000 fabric-attached MetroCluster configuration.

In this scenario, which front end configuration is required for nondisruptive host LUN failover between sites?

A. an intercluster LIF

B. a stretched Layer 2 network

C. IPv6

D. a stretched VSAN

A company has 20 ESX hosts. Ten of the hosts are connected using FC, and the rest are connected over iSCSI. The FC host HBA queue depth is set to 32, and the iSCSI LUN queue depth is set to 64. The FC hosts are now experiencing random connectivity issues.

In this scenario, what would be the reason for the disconnects?

A. The FC host has a lower queue depth.

B. According to the IMT, unsupported HBA firmware is in use.

C. All of the hosts are part of the same cluster.

D. The queue depth is not consistent across the cluster.

You want to ensure maximum performance of iSCSI LUNs on an AFF A220. In this scenario, which two actions will accomplish this task? (Choose two.)

A. Disable flow control.

B. Configure virtual LAN (VLAN).

C. Enable flow control.

D. Enable jumbo frames.

An administrator reviews the Upgrade Advisor before performing an upgrade of their ONTAP cluster.

What information is detailed in the report? (Choose two.)

A. pre-upgrade checks

B. performance metrics

C. risk exposures D. cluster interconnect checks

An administrator is configuring their Ethernet switches to support an AFF A300 cluster that will be providing iSCSI LUNs to servers. The switches are also used for other traffic from various hosts.

In this scenario, which statement about the switch configuration is correct?

A. Use a larger MTU size at the SAN connection rather than the host connections to allow for greater SAN bandwidth.

B. Use network ports as access ports only.

C. Use multiple VLANs to segregate iSCSI traffic from other traffic types

D. Use a single VLAN to consolidate all data traffic on the switches.

Click the Exhibit button.

You connected your FAS8200 to a Brocade SAN switch. As shown in the exhibit, port 0e is not available. In this scenario, which statement is correct?

A. The incorrect SFP+ module is installed.

B. The switch zoning is using the FC nodename.

C. The incorrect firmware revision is installed.

D. The switch port is configured for mode E_Port.

On your ONTAP 9.5 cluster, you need to set up the onboard key manager with hardware-based security and volume encryption.

Which two licenses are required in this situation? (Choose two.)

A. FDE

B. TPM

C. VE

D. RSA

A customer recently added two nodes with FC ports to a 4-node cluster.

Which SVM configuration is needed before the customer creates LUNs on the new nodes?

A. The FC service needs to be enabled on the data SVM.

B. The existing LIFs need to be migrated to the new nodes.

C. New FC LIFs need to be created on the cluster SVM.

D. New FC LIFs need to be created on the new nodes.