Which two statements about SLA targets and SD-WAN rules are true? (Choose two.)

A. Member metrics are measured only if an SLA target is configured.

B. SLA targets are used only by SD-WAN rules that are configured with Lowest Cost (SLA) or Maximize Bandwidth (SLA) as strategy.

C. When configuring an SD-WAN rule, you can select multiple SLA targets of the same performance SLA.

D. SD-WAN rules use SLA targets to check if the preferred members meet the SLA requirements.

Refer to the exhibit.

Which statement about the command route-tag in the SD-WAN rule is true?

A. It enables the SD-WAN rule to load balance and assign traffic with a route tag

B. It tags each route and references the tag in the routing table.

C. It uses route tags for a BGP community and assigns the SD-WAN rules with same tag.

D. It ensures route tags match the SD-WAN rule based on the rule order

Refer to exhibits. Exhibit A.

Exhibit B.

Exhibit A, which shows the SD-WAN performance SLA and exhibit B shows the health of the participating SD-WAN members. Based on the exhibits, which statement is correct?

A. The dead member interface stays unavailable until an administrator manually brings the interface back.

B. The SLA state of port2 has exceeded three consecutive unanswered requests from the SLA server.

C. Port2 needs to wait 500 milliseconds to change the status from alive to dead.

D. Check interval is the time to wait before a packet sent by a member interface considered as lost.

Refer to the exhibit.

Based on output shown in the exhibit, which two commands can be used by SD-WAN rules? (Choose two.)

A. set cost 15.

B. set source 100.64.1.1.

C. set priority 10.

D. set load-balance-mode source-ip-based.

Refer to the exhibit.

Multiple IPsec VPNs are formed between two hub-and-spokes groups, and site-to-site between Hub 1 and Hub 2 The administrator configured ADVPN on the dual regions topology

Which two statements are correct if a user in Toronto sends traffic to London? (Choose two )

A. Toronto needs to establish a site-to-site tunnel with Hub 2 to bypass Hub 1.

B. The first packets from Toronto to London are routed through Hub 1 then to Hub 2.

C. London generates an IKE information message that contains the Toronto public IP address.

D. Traffic from Toronto to London triggers the dynamic negotiation of a direct site-to-site VPN.

An administrator is troubleshooting VoIP quality issues that occur when calling external phone numbers The SD-WAN interface on the edge FortiGate is configured with the default settings, and is using two upstream links One link has random jitter and latency issues and is based on a wireless connection

Which two actions must the administrator apply simultaneously on the edge FortiGate to improve VoIP quality using SD_WAN rules?

A. Select the corresponding SD-WAN balancing strategy in the SD-WAN rule.

B. Choose the suitable interface based on the interface cost and weight.

C. Use the performance SLA targets to detect latency and jitter instantly.

D. Place the troublesome link at the top of the interface preference list.

E. Configure an SD-WAN rule to load balance all traffic without VoIP.

Refer to exhibits.

Exhibit A shows the firewall policy and exhibit B shows the traffic shaping policy.

The traffic shaping policy is being applied to all outbound traffic; however, inbound traffic is not being evaluated by the shaping policy.

Based on the exhibits, what configuration change must be made in which policy so that traffic shaping can be applied to inbound traffic?

A. The reverse shaper option must be enabled and a traffic shaper must be selected

B. The guaranteed-10mbps option must be selected as the reverse shaper option.

C. A new firewall policy must be created and SD-WAN must be selected as the incoming interface.

D. The guaranteed-10mbps option must be selected as the per-IP shaper option

Refer to the exhibits.

ExhibitA shows the system interface with the static routes and exhibit B shows the firewall policies on the managed FortiGate.

Based on the FortiGate configuration shown in the exhibits, what issue might you encounter when creating an SD-WAN zone for port1 and port2?

A. port2 is referenced in a static route.

B. port1 is assigned a manual IP address.

C. port1 and port2 are not administratively down.

D. port1 is referenced in a firewall policy.

Refer to exhibits.

Exhibit A shows the firewall policy and exhibit B shows the traffic shaping policy.

The traffic shaping policy is being applied to all outbound traffic; however, inbound traffic is not being evaluated by the shaping policy.

Based on the exhibits, what configuration change must be made in which policy so that traffic shaping can be applied to inbound traffic?

A. Create a new firewall policy, and the select the SD-WAN zone as Incoming Interface.

B. In the traffic shaping policy, select Assign Shaping Class ID as Action.

C. In the firewall policy, select Proxy-based as Inspection Mode.

D. In the traffic shaping policy, enable Reverse shaper, and then select the traffic shaper to use.

Refer to the exhibit.

Based on the exhibit, which two actions does FortiGate perform on traffic passing through the SD-WAN member port2? (Choose two.)

A. FortiGate performs routing lookups for new sessions only after a route change.

B. FortiGate marks the routing information on existing sessions as persistent.

C. FortiGate flushes all routing information from the session table after a route change.

D. FortiGate always blocks all traffic after a route change.