Where should the administrator set the parameter in the Host Properties to enable failed restore jobs to automatically retry on Client1?

A. Clients > Client1 > Universal Settings > Restore retries

B. Master Server > Client Attributes > Client1 > General > Restore retries

C. Clients > Client1 > Client Settings > Restore retries

D. Master Server > Client Attributes > Client1 > Restore retries

An administrator has a backup policy with the following policy attributes: 3 paths listed in the Backup Selections list 5 clients listed in the Clients list Allow multiple data streams is selected Limit Jobs per policy is set to 4 How many jobs go Active when the job is started, excluding parent jobs?

A. 3

B. 4

C. 12

D. 15

An administrator has a backup policy with the following attributes: 5 paths listed in the Backup Selections list 3 clients listed in the Clients list Allow multiple data streams is selected Max Jobs per Client value set to 4 How many jobs go Active when the job is started, excluding parent jobs?

A. 8

B. 9

C. 12

D. 15

Refer to the exhibit.

What is the outcome of the policy shown in the exhibit?

A. The client encrypts then compresses the data before sending it to the Media Server.

B. The client compresses and the Media Server encrypts the data before sending it to the tape drive.

C. The client compresses then encrypts the data before sending it to the Media Server.

D. The client sends the data to the Media Server, which compresses and then encrypts the data.

What happens if the Maximum data streams property is enabled for a particular client?

A. NetBackup ignores Maximum jobs per client and uses either Limit jobs per policy or Maximum indexing jobs per indexing server, whichever is lowest

B. NetBackup ignores Maximum jobs per client and uses either Maximum data streams or Limit jobs per policy, whichever is lowest

C. NetBackup ignores Maximum indexing jobs per indexing server and uses Maximum jobs per client or the Limit jobs per policy, whichever is lowest

D. NetBackup ignores Limit jobs per policy and uses either Maximum data streams or Maximum jobs per client, whichever is lowest

How frequently does content router queue processing (CRQP) run, by default?

A. every 6 hours

B. every 12 hours

C. every 24 hours

D. every week

On which system(s) is the NetBackup 7.6.1 LiveUpdate agent installed by default?

A. Master Server only

B. Master Server and Media Server only

C. Master Server, Media Server, and client

D. Media Server and client only

The following storage lifecycle policy was used to back up data from a client.

Storage Lifecycle Policy

Backup to AdvancedDisk

Duplication to tape

Duplication to AdvancedDisk

How should an administrator restore data from the tape using NetBackup?

A. from the BAR GUI, select the tape backup to restore from

B. use bpduplicate command to promote copy 1 to the primary copy

C. from the NetBackup Administration console, promote copy 1 to the primary copy

D. from the NetBackup Administration console, promote copy 2 to the primary copy

A NetBackup Master Server has commenced writing four long-running duplication jobs on an AdvancedDisk disk pool. The value of Maximum concurrent jobs for the storage unit and Limit I/O streams for the disk pool are both set to 4.

There are 35 jobs queued on the Master Server that require this disk pool:

5 replication jobs with priority 9999

10 backup jobs with priority 999

20 duplication jobs with priority 99

Two restore jobs that require this disk pool are then submitted with default priority.

Which job type goes active next?

A. Backup

B. Duplication

C. Replication

D. Restore

An administrator needs to duplicate a backup that completed successfully earlier that same day. How can this be accomplished?

A. locate the original backup from NetBackup Management > Reports > Images on Media, right click and select duplicate

B. locate the policy for the original backup and initiate a manual backup

C. locate the original backup in the activity monitor, right click and select restart

D. locate the original backup from NetBackup Management > Catalog, right click and select duplicate